Cosmopolitan Carpet and rug cleaning logo

Call Us

(817) 265-9031

2226 Michigan Ave

Arlington, TX 76013
}

Business Hours

Mon – Fri : 8 AM – 5 PM
Sat : 8 AM – 12 PM
Sun : CLOSED
Call Us Now
Click to Call

There are a few reasons for this. Using too much detergent or soap, not using enough water, or a faulty vacuum are all reasons for a crunchy carpet. It’s time to ditch the dirty sponge and the expensive shampoo! Follow these tips to get your carpet looking brand new again. Listed below are some other reasons why you might have a crunchy carpet.

Using too much soap

It’s not surprising that a crunchy carpet is an indication of too much soap being used when cleaning. The soap particles that remain after you clean a carpet create a sticky film that attracts dirt and makes it seem dirty again. To make matters worse, the soap also makes your carpet look dull. Consequently, you need to reduce the amount of soap used to avoid a crunchier carpet.

One of the most common causes of a crunchy carpet is improper cleaning. The majority of homeowners don’t know that some cleaning methods can actually make the carpet look more pristine than others. Using too much soap can cause a crunchy carpet, but there are other cleaning methods that are safe and won’t leave a sticky residue behind. While soap can be helpful for cleaning some surfaces, it is a great enemy of carpets.

Using suction to remove dirt and detergent

Using suction to remove dirt and detergent from your carpet leaves residue behind, leaving it hard, scratchy, and prone to attracting more dirt. While using suction to remove dirt and detergent can be effective, it can also leave your carpet feeling crunchy and full of bacteria. Here are a few ways to prevent this problem from occurring. Follow these steps to keep your carpet looking fresh and new.

Hot water extraction cleaning is effective in removing soil from deep within your carpet and requires only a small amount of cleaning solution. Professional cleaners will use a low amount of cleaning solution because it is more effective in removing soil from your carpet than using harsh cleaning agents. A low amount of cleaning solution means that you won’t have to worry about a dirty carpet in a short amount of time. Besides, this method uses a much lower volume of cleaning solution, so it will leave your carpet smelling fresh and free of residue.

Using too much water

Crusty carpets are often the result of over-soaping and the wrong type of shampoo. You should choose a carpet shampoo that is formulated for use on carpets. It is also important to follow the manufacturer’s instructions for dilution. Adding more soap will not make your carpets any cleaner. To neutralize the scent of the shampoo, dilute it with water according to the directions, then spray it on the carpet while it is still wet.

Using too much water will create a sticky residue that will stiffen the fibers of the carpet and act as a magnet for dirt. Traditional cleaning methods will only remove the soil that has stuck to this sticky residue. Also, the sticky residue is potentially hazardous to children and pets because it comes into contact with their skin and breathing issues. If ingested, it can even be harmful to health.

Using a faulty vacuum

Crumbly carpet can be a result of long-term wear and tear from improper vacuuming. In order to correct the issue, you must determine the cause of the crunchiness. While you should vacuum your carpet regularly, you must concentrate on the areas where it crunches the loudest. To solve the problem, apply a stain-resistant coating to the carpet and re-stretch it if necessary.

When using a vacuum, be sure to change the filters. If the dust and dirt have clogged the filter, you can replace it to make the carpet cleaner work properly. It is possible that some of the dirt remains in the deeper fibers left by the typical vacuum. To address this issue, consider buying a better vacuum that is more effective. A vacuum that is designed for carpets can remove more dirt.

Leaving residue on carpet fibers

When you use a steam cleaner, leaving residue on your carpet is normal. It happens after the carpet has been cleaned and pre-conditioned. You can clean a stain by using a white rag soaked in the solution and then wringing it over the stain. Wait for at least 8 minutes, and then wipe the rag dry. Once dry, it can be removed using a second white rag.

Several companies claim to leave no residue on your carpet after they clean it. But, some cleaning solutions do leave some residue, mainly because they contain sodium hydroxide, which forms soap when it comes in contact with oils. The most common oil-based soils on carpets are human sebum, pet dander, and airborne cooking oils. It is important to remove these oils from the carpet in order to avoid leaving residue.

Using a naphtha process

While the naphtha process has its place, it is not recommended for all types of carpets. The resulting carpet is crunchy and prone to attracting abrasive materials. Additionally, it can be difficult to clean due to the odor and can remain on the carpet after use. Fortunately, a neutralizing rinse can be made by mixing one cup of vinegar with one gallon of water. However, if the problem persists, extraction is the only way to go.

After vacuuming a carpet, the particles left behind will be hardened and become embedded in the carpet fibers. These particles will become a magnet for dirt, making it difficult to remove them by conventional methods. The carpet will also become stiffer over time as the residue remains in the fibers. Vacuuming a crunchy carpet isn’t enough to remove dirt and soil that has adhered to the residue.

At Cosmopolitan Carpet we are dedicated to helping you keep your home healthy, clean, and always looking its best. The solution to difficult carpet cleaning is just a phone call away. Call us today, we can help!